CGS66 - ±15V Power Supply

±15V Power Supply for DIY Modular Synthesizers.


This is a PCB only suitable for multiple formats


Note: this project may require wiring a transformer to the A.C mains. This is best left to people who are qualified to do so. Where possible, use a plug-pack, wall-wart or line-lump, or other product where the mains wiring has already been done.

Availability: In stock

$10.99

Details

Details

Note: this project may require wiring a transformer to the A.C mains. This is best left to people who are qualified to do so. Where possible, use a plug-pack, wall-wart or line-lump, or other product where the mains wiring has already been done.

The Power Supply is a companion or alternative to the CGS14 +/- 15 Volt Power Supply. It is suitable for use with VCOs and more "analog" modules. It is of course quite capable of driving the noisier digital modules too, and in all likelyhood will do a better job than the CGS14.

A little on how it works:

 

Power Supply

The schematic for the Power Supply.

 

The incoming AC power is rectified, then filtered. The filtered DC is regulated by the positive and negative voltage regulators. The regulator minimum load requirements are met by placing a LED and its associated resistor between each output and the 0 volt (ground) line. Capacitors are placed close to the input, adjustment and output pins of the regulators to improve stability and transient response. Two additional diodes per regulator protect the regulators should the outputs be shorted together, or should a voltage be fed into the output of the power supply. It is very much a standard configuration, detailed in many data books.

When fed from a 30 volt center tapped transformer (15v-0v-15v) you should be able to pull around 200ma at +/-15 volts from the PSU without problems, and notably more at +/-12V output. If using for +/-15 volts there will be minimal heat generated by the regulators because they will be running close to their minimum voltage drop, though you do risk ripple getting through to the output as the load increases.

When fed from a 36 volt center tapped transformer (18v-0v-18v) you should be able to pull around 600ma, at +/-15 volts, from the PSU without problems. There will be a fair amount of heat generated by the regulators and diodes, so make sure there is adequate airflow around the board. 600ma is close to the maximum D.C. current you can draw from this PSU when powered from a 1 amp transformer. You may also wish to use 3300 mfd 25 volt capacitors instead of the specified 2200 mfd.

Drawing more than 600ma, while possible with a larger transformer, is not recommended, as there is inadequate heatsinking on a number of components, and the electrolytic capacitors are much too close to the heatsinks.

Another factor limiting the maximum current that can be drawn from the unit is the size of the heatsink. With 600ma being drawn, each regulator can easily be dissipating 6 watts, and will require a heatsink with a rating of 12°C/W or better to operate in an ambient of 25°C. As heat in an enclosed space may well be greater than this, I'd recommend going for the best heatsink of the correct profile you can get. Hobby shops in Australia have them available at 8.5°C/W (50 mm) and 11°C/W (40 mm), depending on the shop, though I have used 63 mm heatsinks I salvaged from old switch-mode power supplies. The profile used is simply listed as PCB mount TOP-3 in the local catalogs.

As a note of interest, the prototype was tested running from a HP printer line-lump with a 10v-0-10v coil, the supply outputting +/-12 volts for driving Eurorack modules.

Specs & Downloads

Specs & Downloads

manufacturer CGS
HP No
Depth No
+12V No
-12V No
+5V No
Additional Resources BOM & More Information

Reviews

Write Your Own Review

You're reviewing: CGS66 - ±15V Power Supply

Tags

Tags

Use spaces to separate tags. Use single quotes (') for phrases.