CGS38 - Saw Pitch Shifter

The Saw Pitch Shifter is an experimental combination of op-amp summers and comparators with surprising results, ranging from complex wave shaping to pitch shifting of saw tooth waves in your modular synthesizer.


This is a PCB only suitable for multiple formats


Availability: In stock

$10.99

Details

Details

The Saw Pitch Shifter is an experimental combination of op-amp summers and comparators with surprising results, ranging from complex wave shaping to pitch shifting of saw tooth waves.

Some ideas on how to use this module:

As a waveform mangler - feed it any combination of waveforms, or a waveform and a control voltage and adjust as needed. For example, feed a waveform from a VCO or LFO into one input, and adjust the input level for differing effects. Use a control voltage as an offset signal to introduce variation. This can be from an envelope generator, keyboard or LFO or another VCO.

As a sawtooth frequency doubler - feed in a single sawtooth wave, and adjust the associated gain. When the gain reaches 2, assuming a 0 to 5 volt waveform, the result will be a sawtooth of twice the frequency at the first output.

As a sawtooth pitch shifter - feed an audio frequency sawtooth wave into one input, and a sawtooth wave from an LFO into the other. Disable one input using the switch, then adjust the input level of the other input until the LED lights, then back off until it goes out. Disable the other input using the switch, then repeat the procedure for the other input. Return the switch to the center position. The LED will now work as a "signal present" indicator and can be ignored. One output will be the sum of the two frequencies, and the other should be the difference, depending on the relative slopes of the two sawtooth signals. If the result sounds rough, tweak one of the inputs until it sounds clean.

Note that getting the pitch shift to work correctly takes some experimenting and tweaking. The input waveforms should be in the range of 0 to 5 volts - specifically with the bottom of the waveforms actually hitting 0 volts. An external offset may need to be mixed in if this cannot be achieved. The downward shift output is very sensitive to gains and offsets, and is unlikely to be as pure as the upward shift output. If you want a more accurate downward shift, swap the direction of one of the input waves, and upward shift output will act as a downward shift output and vice versa. Some very powerful sound can result, even with impurities in the shifting, especially when the incoming frequency, and the up and down outputs are mixed together.

Also note that this is NOT a frequency shifter - the relationship between the harmonics are preserved.

 

A little on how it works:

 

 
The schematic of the Saw Pitch Shifter/Wave Multiplier.

 

The first half of the circuit is essentially a mixer. The two incoming waveforms are buffered the sent through the "setup matrix" that allows grounding of one signal or the other to help setting up the signal levels. The two signals are then summed and fed to another summer and a comparator. The second summer adds the voltages from the comparator, and a fixed reverence voltage that compensates for the offset introduced by the comparator.

Note that the processing between the two summers actually occurs while the signal is inverted. If the output of the first summer exceeds the preset value of 5 volts, the comparator output changes, subtracting 5 volts from the total present at the output. This means that if the instantaneous voltage of an incoming wave has passed 5 volts, it will suddenly be converted to 5 volts - 5 volts (i.e. 0 volts) where it will continue to rise at the previous rate until it reaches its peak. When the waveform again falls below 5 volts, the comparator will switch back, restoring the original input output relationship. The LED lights whent he comparator is subtracting 5 volts from the output.

The downward shift output is generated in much the same way, with the exception that the second incoming signal is inverted and offset before being fed into the associated summer. There are no setup matrix present or monitoring LED for this output.

Specs & Downloads

Specs & Downloads

manufacturer CGS
HP No
Depth No
+12V No
-12V No
+5V No
Additional Resources BOM & More Information

Reviews

Write Your Own Review

You're reviewing: CGS38 - Saw Pitch Shifter

Tags

Tags

Use spaces to separate tags. Use single quotes (') for phrases.